TEXAPON P
TEXAPON P
Technical Datasheet
TEXAPON P is a mixture of highly effective surface-active substances.
TEXAPON P is used as highly active wetting and dispersing agent for emulsion paints based on PVAc, polyacrylates and their copolymers.
TEXAPON P improves substrate adhesion and enhances the penetration of wood coatings.
Product Type
Dispersing Agents > Surfactants-like
Wetting Agents / Wet Edge Enhancers > Surfactants
Use: TEXAPON P is Emulsifier for emulsion polymerization, wetting agent for dispersion paints
Composition: Mixture of highly effective surface-active substances.
Specification Viscosity at 20 °C 400 – 600 mPa·s (DIN 53015)
pH-value (10% 6.5 – 7 aqueous solution / Q-P 1205.2)
Anionic surfacant 20.5 – 22.5 (Q-C 3602.0)
Additional data
Appearance: clear, yellowish liquid of medium viscosity
Density at 20 °C: approx. 1.05 g/cm³
Ionic character: anionic/non-ionic
Sulphate < 1.0%
Chloride < 0.5%
Application (Polymerization)
TEXAPON P is an emulsifier for the manufacture of emulsion polymers, especially for
-acrylate homo and copolymers,
-styrene-acrylate copolymers,
-vinyl acetate homo and copolymers,
-vinyl acetate/versatic acid vinyl ester (Veova) copolymers.
Dosage (Polymerization)
TEXAPON P may be mixed with anionic and non-ionic emulsifiers in any ratio. Even in very hard water it does not cause formation of lime soap.
The incorporation amount depends on the type and quantity of the initial monomers as well as on the polymerization process and the desired properties of the polymer dispersion.
In general, 0.5 to 2.5% of TEXAPON P (100% active substance) is used, calculated on monomers weight.
TEXAPON P is suitable as a single emulsifier but a combination with non-ionic coemulsifiers of the Disponil NP, Disponil AAP, Disponil LS or Disponil TA type is possible.
Application (paints)
TEXAPON P is a highly active wetting and dispersing agent for emulsion paints based on PVAc, polyacrylates and their copolymers.
Texapon P facilitates the incorporation of difficult-to-wet pigments such as Hansa yellow, toluidene red and phthalocyanine pigments.
Texapon P improves substrate adhesion and enhances the penetration of wood coatings.
TEXAPON P may also be used in the manufacture of tinting pastes to ensure their easy and uniform dispersion into emulsion paints.
Dosage (paints)
In paints: approx. 0.3%,calculated on total batch
In tinting pastes: 5 – 10%, calculated on total paste
Regulatory Status DSL, TSCA, EINECS, AICS, ENCS/MITI
Miscellaneous TEXAPON P has good biodegradability.
The product meets the legal requirements of the German Detergents Law as well as all legal requirements of the EEC Directives.
Texapon P is recommended to store TEXAPON P at room temperature and to protect it against influences of heat and frost.
If stored in the original sealed containers the product is durable for at least 1 year
Mixture of highly effective surface-active substances.
Texapon P is used as highly active wetting and dispersing agent for emulsion paints based on PVAc, polyacrylates and their copolymers.
Improves substrate adhesion and enhances the penetration of wood coatings.
Texapon P is characterized by a very high active substance matter and a very low content of inorganic salts and unsulfated fatty alcohol.
The preferred areas of application for Texapon P are toothpastes, emulsion and cream shampoos.
Texapon P is an alkyl sulfate on the basis of a natural, saturated, primary fatty alcohol with good foam behavior and cleaning performance.
Description
Texapon P is a foaming agent derived from alcohols based on natural, renewable oils and fats, characterized by a very high active substance matter and a very low content of inorganic salts and unsulfated fatty alcohol.
Texapon P has excellent cleansing and foaming efficacy.
Preferred areas of application are pharmaceutical emulsion and cream shampoos.
Supplied as a white to off-white powder with faint characteristic odor.
Convenient in handling and storage
Excellent flowability
High bulk density
Tight particle size distribution